Wednesday, July 14, 2010

stator replacement

The replacement for the 90 stator is ready, it has a mark to check the points and a bolt screwed in from the back, that holds the oil pump gear in place.

Too bad the aluminium turned out to be really soft, when I tightened the three bolts, the aluminium expanded, actually causing it to get pushed outwards against the casing.....
For now I'll let it be, and get on with building the rest of the engine, but I think this part will be replaced by something of better quality.

front brake

The CB72 is ready again for the event in Lelystad next weekend. I had some trouble with the front brake, Honda 200mm drums are too light, when really used, they grow so much from the heat that the spokes become loose. From one of my dad's other CB72 racers came a front wheel with Suzuki T500 front drum, now fitted with a honda brakeplate. These hubs have a thicker lining and can withstand the abuse of racing with modern tyres.

New silencer from Honda

I was just looking around the CMS website, when I came across this new model silencer from Honda.



I think its cool, I just don't have the "model" this plugs into.
they also have a red version.

Sunday, July 11, 2010

RSC rotor

On the 90 I will not be using the original rotor and stator assembly, to save weight on the cranck, and in total, I will be running a battery ignition that will be recharged before every event.
But to check the ignition timing and valves, I need something to determine "Top" and "Fire".
I bought a ct90 rotor from Loef that I modified.


All the weight has been taken off, leaving just the center with the cone and slot for the woodruff key. Onto this I bolted an alloy disc (bolts will be replaced by original honda cross-head bolts)

And then copied the markings from the original CS90 rotor onto the alloy disc.

This rotor will be permanently mounted to the cranck, as I don't want the hassle of putting it on every time I need to check something.
Next step will be an alloy ring to replace the stator, it will have the mark for timing and something to keep the oil-pump shaft in place.

Racing at Purmerend

Last week we had an event in Purmerend at a closed off industrial area. I raced my 50 and my dad's CB72 to compete in 2 classes. This was the third event I rode the 250 to see if I would like the "big" bike.
Action shots are thanks to Lea langezaal, the club photographer, see more of her pictures on the CRT website
The number 2 bike is an Aermacchi.


Unfortunately in the last heat, the motor shot out of gear, or so it seemed, I was quick with the clutch, had a look if I could see anything wrong, but nothing to see. I tried to release the clutch gently, but that didn't feel right, so I quit.

Back home, we took out the engine, my dad has three of these bikes, and raced them with friends. Back then, the bolt that alligns the shift fork with the shift drum had broken before, so that was believed to be the problem. But when we opened the clutch cover, the real problem became all to clear: broken primairy chain.

This is a "normal" thing to happen to a CB72, especially when raced, but usually the chain cracks the cluch cover making it clear what happend, in my case it didn't even leave a scratch on the inside.
Fortunately my dad had a new stronger chain set ready to fit to this engine, just didn't get round to fitting it yet.

Monday, July 5, 2010

progress on the 90

I've done some work on my RSC90 project as well, assembled all the clutch parts and fitted the cover, with breather unit.

Also fitted the bigbore piston and cilinder, although it has to come off again because I can't remember if I put the knock pin in. I hope I did because the pistonrings were a pain to get in, when the cilinder was bored out, the sloping edge has disappeared.

Chain tensioner has been put in after this picture was made, but I have to figure out a way to keep the oil-pump sprocket in place as I don't want to use the stator which normally keeps it from moving side to side.

pictures from down under

I recieved some more pictures from Stew's RSC90 project.


He found an original honda stand for only 10 dollars at a swap meat. Think it's from an MT125 or RS125 2stroke racer, but I'm not sure, my stands were homemade from pictures.
Note the details, MT125R top yoke, lightened rear sprocket and everything else.

Thursday, June 24, 2010

Long stroke experiment

Sadly the experiment didn't turn out to have a big effect.
After a lot of fine tuning it might give a little bit more then the current short stroke motor, but not enough to make a real impact in the 2stroke dominated 50cc class. So I'm thinking of quitting the 50cc altogether to focus on my RSC90 and maybe a CB72 that I've been trying for the last two events.

For now the 50cc has been converted back into a short stroke, with some minor adjustments to the head, valves and camtiming to get power at higher revs.
Next weekend is the Honda-day with a dyno, lets see what the little 50 has to give.

Friday, June 18, 2010

Long stroke experiment

A new experiment to get some more torque out of the 50cc engine, as it is originally a short stroke, at 35,6mm with a 42mm bore.
Now a test using an XR75 cranck wich has a 41,4mm stroke, just like an SS50.

Cylinder is sleeved to get to a 39mm bore, combined with a GB2 piston, originally of an engine with horizontal cylinder.

Tomorrow its first run....

R90/6 café transformation

The transformation into a caferacer has begun.
Clip-on handlebars, found in the spareparts bin of my dad's racing history, originally 35mm but adapted for the 36mm BMW forks.
Under the black paint, it turned out I had a chromed top fork plate in good condition.

Real magura's, no modern stuff.

And the Laverda SFC tophalf fairing I want to put on. I started with a different style tophalf, but that didn't have enough height to fit the headlight.