Monday, November 8, 2010

more new parts on the oldschool engine

New crankcase for the "old school engine"
well, not exactly new, it comes from a used C65 motor. I wanted these because of the mounts underneath the cilinder for a guard plate. At some point an oilcooler will be mounted on here.
After glassbead blasting:


Nice that there is no engine number, the old engine must have had the cases swapped at some point.
BUT.....these are 1960's cases, this means problems like I've encountered with the S90 motor, but didn't expect on this.
different locations for the guide pins, should both be be on the top tappets in this picture, but they are not, so I can use only one that corresponds with my cilinder.

A hole, my piston for the camchaintensioner will not block this and won't be able to build up pressure, will have to find/make a longer piston.

The piston I had in the other cases, with the long spring. And the short spring that was with the C65 cases, this tells me I need a longer piston.

new clutch for the ss50 engine

I have been collecting parts for my "old school tuning" ss50 engine, to replace the original clutch with one from a C110.
The C110 has an aluminium center that weighs a lot less then the original ss50 clutch. Although my engine had a 2plate clutch from a chinese copy. even more weight then the original 1plate, but it was the only complete clutch I had laying around at the time.
C110 clutch:

Only it doesn't fit onto an SS50 crankshaft without modification, so I had my dad grind the inner diameter to fit the SS50 crank, then the splines fit.

On all sides it needed some work, the primairy sprocket needed some work to fit onto the gearbox main shaft. Some spacers needed to fit the whole clutch onto the crank, and a bearing holder had to be fabricated to let oil thru, as the c110 doesn't have that.


To give an idea about the weight loss
2 plate:



C110 clutch:


Now to finish the engine so I can hear the difference in revving, I'm looking forward to starting this up and hearing the difference.


A nice bonus is the difference in primairy reduction.
SS50 originally has 16:69.
my 2plate system had a 17:67 reduction.
And the C110 has 15:70. this means the gearbox will make less revs, letting it shift easier.

90 valves

The valves for the 90 have been done.
Thinned down the shaft for the length it sticks into the port with full lift on the cam.
This means more space for fuel to get thru and a reduction in weight, this will help in the higher revs.
Also they have been ground into the seats to see where the contact is, and the edges sticking out have been removed and rounded to let fuel pass by the valve easier.




Also removed weight from the side of the valve that is in the combustion chamber, the loss in compression is minnimal, but you will notice the reduction in weight.

Sharp edges removed from the combution chamber.
Now only to wait for my titanium valve spring retainers to come in and then the engine can be completed.

Sunday, October 24, 2010

we're back

I've had a slight computer problem, but I'm back online now.

In the meantime I've recieved some nice packages in the post.
12" sidecar wheel I just couldn't let it pass me by.
Seen here next to the 16"front wheel of my dad's sidecar racer

You don't have much opportunities to get these, and it might look great on my dad's Oudshoorn BMW.

Also bought some nice carbs on ebay for my own BMW, because I'd like to determine the position of the throttle slide instead of it being "automatic" like in the original carbs.
These are 36mm BING off an R75/5.
But I will have to alter my footrests first or my foot will get jammed between the shifter pedal and the lower part of the float bowl.
This will be a winter project.


Today I checked the oil levels of the driveshaft, gearbox and final drive, because I had some leaks. Might be a seal put in backwards by a previous owner, this will be checked in winter, for now the levels are correct again.
But when working on the back, the broken rear fender began to really bother me.
The mudflap covered the damage, but I wanted to get rid of the flap because it made my bike look like an old geesers machine.
So I took the grinder and reworked the rear end.

Looking a lot more sporty now. I want to do more to it, but for that I would need to take out the fender, not something I want to do when I need to take the bike home again, or rather, it had to take me home again.

Saturday, October 2, 2010

screw-ons mounted

Today I mounted the new screw-ons.
here you can see a new one mounted and an old one still on the right (of the picture)

A lot of difference in the height and the angle, on my way home I allready found it a lot more comfortable.

Original throttle controls:


Drivers view:


Because I have a twin leading front brake off a CB125k1-5 my front brake cable has an 8mm ferrule, where an SS50 only has a 7mm ferrule. This was never a problem because I used CB-type levers and switches, but now my brakecable wouln't fit into SS50 type switches so I had to machine something to match an 8mm cable to a 7mm hole.


By the way, my old set of screw-ons is now for sale.

Wednesday, September 29, 2010

screw-ons

On most of my bikes I have clip-on handlebars, but on my SS50z I wanted to maintain the original headlamp stays, so I made fake clip-ons for it, I call them "screw-ons" because they are mounted with the top fork bolt.
I had two sets of these before, that I found on ebay, but they have been sold, the set that is now on my SS50z was homemade, to look lower, but I took a guess about the angle of the bars and that turned out to be too much downwards.

Now I've been making a set to replace them.
All parts together before welding:

The slots have been milled out at a 5 degree angle, this is a standard measurement for clip-ons (5, 10 or 15 degrees)
I didn't want it to be straight, that would look to simple and to much like zündapp clip-ons.

I asked my dad to weld the bars with copper, less warping and I might want to have these chromed in the future, I don't know if that would be possible if these were welded with silver.
For now, painted black (frame colour) just like the 60's racebikes.
Slots have been milled out for the original SS50 throttle controls and for the wires to go thru the bars, even if it is only for 5cm.

Note the levers with little ball ends.

Underside, throttle cable comes out thru an original rubber grommet.

I hope to mount them on my bike tomorrow after work, if there is no overtime.

Sunday, September 19, 2010

Rockers

Lightened rockers for the 90, about 10% lighter then original.
It does take some time to do this, but it is nice old school tuning.



And a nice points cover I scored on Ebay, originally off an ATC110.

ribbed for extra cooling, I think I'll need it as I do not want to install a "modern" oilcooler.

Wednesday, August 4, 2010

New camshaft

Today in the mail I recieved a new hot camshaft for the 90 that I had won on ebay. Didn't have much info when I bought it about timing and lift, So I was hoping it would be different from the hotcam I allready had. And I was lucky.
From left ro right: original S90 cam, hotcam #1, hotcam #2




More lift and duration, looking forward to building the 90 engine again, it has been on a bit of a standstill.
The racers needed work and I am making new handlebars for my moped, time is scrace during racing season.

unknown piston

My dad is building an 85cc race engine based on an XR75 (post 1976), it is for a friend who will race it at a moped racing club.
This guy brought over a lot of parts to build with, including a big bore piston.
I like this piston, for the 50mm bore that is was originally built for, this one is a 50,75mm bore, 3rd oversize.
This has a 13mm piston pin, just like xr75.
But this piston didn't have any original box, or any markings, so I don't know what it is.

Can you help me identify this piston????

50mm standard bore
13mm piston pin
And very distinctive valve indentations.
But I can't even be sure it is honda, it might be something else.
If you have any idea what this is, please send me an email.






Tuesday, July 20, 2010

How to make a cable

For the RSC90 I've made all the cables by altering original or aftermarket honda grey cables, like I've done for my other bikes. A while ago, someone asked me to write it all down and make somewhat of a manual for altering cables.
Well here is the method I use, from what I know, I think this is the best way to do it.
But, in this modern world of prosecuting people, I take no responsibility for the cables you alter, this is just a guideline.

I start with a Honda or aftermarket cable, I like grey, but this can also be done for black cables of course.
This example is of a front brake cable for a twin leading Honda front brake, normally I would shorten this from the top, but in this example I used a cable that was already cut at the bottom and added the original adjusters to it, that have been taken off old cables before they were thrown away.

You start with cutting the inner cable at the nipple that you want to replace.
Then you take out the inner cable, and cut the outer cable to length.
I use an angle grinder for all cutting, this leaves clean straight cuts, do not use wirecutters for the outer cable, the uneven end could screw itself into the inner cable, blocking the function. You need a flat end off the outer cable:

Now you replace the ferrules at the ends that have been cut off, in my case this is the big adjuster that goes onto the brakeplate. Sometimes it is possible to take off the old ones from the end that is cut off, but is is much easier to buy new ones. I get my supplies from the cable-shop.
Now you want to put everything onto the cable, it wouldn't be the first time someone has it all soldered only to find out he forgot the adjuster that has no slot to slide it onto the cable afterwards.

Now you unraffle the inner cable (the steel nipple on this cable is homemade to fit the twin leading hub, nipples for the top to fit into the levers are normally available) the nipple is also fitted, as it can be difficult to get it on after the cable has been rewinded.

The outer wires are oppositely wound to the inner wires.
Take the inner wires and unwind these also, this will have a straight wire in the middle, cut this down about 1cm.

After this, rewind the inner cables, and then the outer cables, when done correctly, this will leave you with a normal looking cable, but with a small hole on the end.
Sadly my camera couldn't really get this clear.

Now you take a piece of steel wire (not stainless) about 2mm diameter, and make a wedge out of it, I do this by rotating it against an anglegrinder with a sanding disc.

Cut it off, long enough so you can still handle it.
Then it is inserted into the hole on the end of the inner cable so that it is spread outwards and the nipple is pushed onto this.
You should be able to pull on the nipple without pulling it off the cable, even before the wedge is soldered into place. This way, the strength comes from the cable being wedged into the nipple instead of the solder, this will just keep the wedge from falling out.

The tools for the job:

Use the flux on the parts you want to solder, heat the nipple and cable and then apply the solder (tin/lead) from the bottom where the wedge sits. (use silver for stainless cables)

Stop when you see the solder creeping thru the cable at the top of the nipple.
At this point, let it cool gently, afterwards you can grind away the excess parts of the wedge and/or cable. Now you can mount your cable.

This method will work on clutch and throttle cables also, with throttle cables it isn't always necessary to take out the middle strand, as the strands are thinner and more flexible.

I wish you good luck altering your cables, and if you have questions, don't hesitate to ask.